How To Ground A 200 Amp Service Panel

how to run a ground wire to an electrical panel

When talking nigh electrical safety, 1 of the chief topics that should be discussed is the existence of ground wires.

Although ground wires are non required for an electrical musical instrument to work properly, attaching basis wire to electrical box is a norm for electricians because it provides an boosted safety feature that can save your life in accidents.

Normally, ground wires do not carry current. Current volition just pass through ground wires when there is an excessive corporeality of it or the original path has been damaged.

If you lot're wondering how to run a ground wire to an electrical panel, go on reading!

Table of Contents

Tool For Connecting Your Ground Wire to An Electric Panel
Steps on How to Connect Basis Wire to Electrical Panel
- Step 1. Basis bar or rod Installation
- Footstep two. Attach your footing wire to the ground rod
- Footstep three. Keep the breakers off
- Step 4. Remove panel cover
- Stride 5. Selection a proper knock-out hole
- Stride vi. Locate neutral bar or grounding bar
- Step seven. Connect the basis wire to the bar or rod
- Step 8. Finish up
Importance of Grounding
Conclusion

Tool For Connecting Your Ground Wire to An Electrical Panel

attaching-ground-wire-to-electrical-box

Ground bar or rod

Regarding the materials to be used in ground rods, it is highly suggested that you employ galvanized steel, stainless steel, or copper-bonded steel. Among these three, galvanized steel is the cheapest and ofttimes preferred past experienced electricians.

Mallet
Screwdriver
Ground wire (ordinarily a 6-gauge copper wire or bigger)
Clench
Multimeter
Protective equipment

Steps on How to Connect Basis Wire to Electric Panel

Step 1. Footing bar or rod Installation

connect-the-ground-wire

The starting time step in running a ground wire to your electrical console is to first know where you lot desire the backlog electric current to menstruum. Since you cannot just leave your ground wire hanging or attached to the footing, you need a ground bar or basis rod where your basis wire will exist continued.

It is suggested that you bury the rod upwardly to 8 feet below ground and leave three to 4 inches above the ground where your basis wire volition be fastened.

If all weather condition are met, you may start driving your ground rod to the soil outside your house with a mallet. Make sure a passerby won't stumble on the above-ground rod where your wire is being connected.

Pace 2. Adhere your ground wire to the ground rod

Connect the ground wire to the rod using a clamp. Secure the connection.

Pace 3. Keep the breakers off

ground-wire-go-in-electric-panel

Before doing electrical installations, information technology is imperative that you should always check your breakers and keep them off, unless you lot are about to test your piece of work.

Turning off your breakers will let you piece of work safely and avoid electrical impairment or even electrocution.

Step four. Remove panel cover

Almost electric panel covers or faceplates are intact by screws. To remove the panel comprehend, get a proper screwdriver to be used, either a flathead screwdriver or crosshead-screwdriver, depending on what screw heads were used.

Step five. Option a proper knock-out hole

The knock-out hole is a detachable part on the panel'southward surface where wires that should be inserted within the panel are threaded.

Know the location of the proper knock-out hole to be used, depending on where you lot put your basis bar. Pick a pigsty where the footing bar or footing rod is nearest.

Pace half dozen. Locate neutral bar or grounding bar

Near electric panels have a grounding bar built inside where ground wires should be fastened. Still, there are some electric panels where at that place are no congenital-in ground bars. If that is the case, your ground wire should be fastened to the neutral bar.

Step 7. Connect the footing wire to the bar or rod

connect-ground-wire-to-electrical-panel

Using a #6 gauge copper wire, kickoff attach i terminate of the wire in the ground bar or neutral bar inside the electrical panel. Make certain you lot insert the wire through a knockout hole near the ground rod located outside the house to minimize the unnecessary bending of the grounding wire.

Carefully set up the ground wire until information technology reaches the ground rod located outside the house. You may utilize wire ties if necessary to avoid wire tangling.

On the other end of the wire, make sure that the end is completely attached to the basis bar in order to completely eradicate the possible loosening of the basis wire.

Likewise, the wire should non hinder any pathways. Brand sure likewise that the footing wire is costless from thorns or amercement.

Stride eight. Terminate upwardly

Switch the breakers on and and so start testing. Do non forget to use personal protective equipment when dealing with electrical testing.

You may employ a multimeter to exam for resistance. It should be shut to Zero "0" to say that grounding is effective.

If everything went perfect, close the faceplate and administer the screws into their original places.

Importance of Grounding

Grounding is the process where you attach a basis wire into the grounding bar to forbid backlog current from flowing through undesired locations.

We can all agree that the chief purpose of grounding your electric panels, even appliances, too, is to prevent electrocution when the normal path of electric current is damaged or accounted unserviceable.

Having your electrical panel grounded, you then keep all your outlets grounded since all outlets in your firm must be connected through an electrical console, which serves as the main free energy source.

Research says more one decease per solar day happens due to electrocution in the Usa alone. Having an extra layer of safety features in your house is the all-time matter to practice to eliminate or mitigate risks that can put your life at stake.

Conclusion

After reading this commodity, yous should now know how to run a ground wire to an electrical panel.

Whenever working with electronics and electrical wiring, safety should exist our utmost priority. Condom precautions should not terminate subsequently completing the job considering there are other chance factors that may lead to serious injury or even death.

Attaching a footing wire to an electric box mitigates the risk of injuries or even electrocution. Share this article if you feel that others might want to know well-nigh this too.

I am Edwin Jones, in charge of designing content for Galvinpower. I aspire to use my experiences in marketing to create reliable and necessary information to aid our readers. It has been fun to work with Andrew and use his incredible cognition to our content.